Vocal Chain Cheat Sheet: Plugin Order and Starting Settings
The plugin order for a lead vocal with a starting value for each step, how the chain changes for rap, trap, pop, R&B and rock, and the rules behind it.
- Order: gain staging → pitch correction → subtractive EQ → compressor → de-esser → additive EQ → second compressor/limiter → saturation → reverb and delay on sends.
- High-pass: 70–100 Hz (male), 100–120 Hz (female).
- Compressor: 3:1–4:1, attack 10–30 ms, release 50–100 ms, 3–6 dB reduction.
- De-esser: 5–8 kHz, 3–6 dB.
- Air: +2–3 dB shelf from 10–12 kHz.
Vocal chain order and starting settings
A typical insert order for a lead vocal, with starting values. Use your ears: every voice, mic and room needs different amounts.
| # | Plugin | Starting settings |
|---|---|---|
| 1 | Clip gain / gain staging | Even out loud and quiet phrases so the vocal peaks around −18 to −12 dBFS going into the chain. |
| 2 | Pitch correction (optional) | Before the compressor, so it reads clean notes. Natural: slower retune speed; modern rap/pop effect: fast. |
| 3 | Subtractive EQ | High-pass at 70–100 Hz (male) or 100–120 Hz (female); cut boxiness at 200–400 Hz or harshness at 2.5–4 kHz only if you hear it. |
| 4 | Compressor 1 (shape) | Ratio 3:1–4:1, attack 10–30 ms, release 50–100 ms (or auto), 3–6 dB of gain reduction on the loud parts. |
| 5 | De-esser | Centred around 5–8 kHz (sibilance), 3–6 dB reduction on the "s" and "t" sounds only. |
| 6 | Additive EQ | Presence +1–3 dB around 3–5 kHz, "air" shelf +2–3 dB from 10–12 kHz; a little 150–250 Hz for warmth if the voice is thin. |
| 7 | Compressor 2 / limiter (control) | Fast attack, ratio 4:1–8:1 or a limiter, catching only the peaks: 1–3 dB of gain reduction. |
| 8 | Saturation (optional) | Subtle tape or tube saturation for density and presence; mix 10–30%. |
| 9 | Sends: reverb and delay | Reverb on a send with 20–80 ms pre-delay; a 1/4 or 1/8 note delay (see the delay calculator), both EQ'd (high-pass ~200 Hz, low-pass 6–10 kHz). |
Settings for every element on one map
MixMap gives frequency, pan, width, level, compression, reverb and delay starting points for 63 elements across Pop, Hip-Hop, R&B, Electronic and Indie. Click an element to get its settings.
How the chain changes by genre
| Genre | Processing | Space and effects |
|---|---|---|
| Rap / hip-hop | More compression (5–8 dB total), bright presence, short room or plate | Upfront and dry; delay throws on line endings |
| Trap | Fast pitch correction, two compressors, bright air | Doubles and ad-libs panned wide; delay on ad-libs |
| Pop | Two-stage compression, smooth de-essing, lots of air | Plate or hall with pre-delay; stacked harmonies |
| R&B | Gentler compression, warm low mids, smooth top | Longer reverb and delays for depth |
| Rock | Parallel compression, saturation, mid-forward EQ | Shorter plate; slapback delay (80–120 ms) |
The rules that matter most
1. Fix before you enhance
Cut problems (rumble, mud, harshness) before boosting presence and air; boosting a problem only makes it louder.
2. Two gentle compressors beat one hard one
Shaping with one compressor and catching peaks with a second keeps the vocal even without sounding squashed.
3. De-ess after compression
Compression and presence boosts make sibilance louder, so de-ess after the first compressor (and again after the EQ if needed).
4. Put space on sends
Reverb and delay on sends let several vocals share one space and keep the dry vocal clear. Detailed values per genre are in the vocal reverb settings guide.
Quick answers
What is the correct order for a vocal chain?
A common order is gain staging, pitch correction, subtractive EQ, compressor, de-esser, additive EQ, a second compressor or limiter, saturation, then reverb and delay on sends.
What compressor settings should I use on vocals?
Start with a 3:1 to 4:1 ratio, 10–30 ms attack, 50–100 ms release and 3–6 dB of gain reduction, then add a fast second compressor or limiter for 1–3 dB on the peaks.
Where should I high-pass vocals?
Around 70–100 Hz for male voices and 100–120 Hz for female voices, lower if the voice sounds thin.
What frequency is sibilance?
Usually between 5 and 8 kHz, so set the de-esser there and reduce the "s" sounds by 3–6 dB.
Should EQ go before or after compression on vocals?
Both: subtractive EQ before the compressor so it doesn't react to rumble or mud, and additive EQ (presence, air) after it.